Saturday, 8 November 2014

PROPULSION-I Questions Bank 2014



PROPULSION-I Questions Bank 2014

Anna University, Chennai

Anna_University,_Chennai_logo

 

16 MARKS QUESTION UNIT - I

1. An advanced fighter engine operating at Mach 0.8 and 10Km altitude where, Ta=223.297K & Pa=0.2649 bar has the following uninstalled performance data and uses a fuel with C.V=

42,800KJ/Kg:

Thrust = 50 KN Mass flow of air = 45Kg/s Mass flow of fuel = 2.65 Kg/s

Determine the specific thrust, thrust specific fuel consumption; exit velocity, thermal efficiency, propulsion efficiency, and overall efficiency (assume exit pressure equal to ambient pressure). 16

2. Find specific thrust and SFC of a simple turbojet engine, having the following component performance at which the cruise speed and altitude are M 0.8 and 10000m. Select ambient condition from the gas table.

Compressor pressure ratio Turbine inlet temperature Isentropic efficiency:

8.0

1200K

Of compressor ηc

0.87

Of turbine ηt

0.90

Of intake ηi

0.93

Of propelling nozzle ηj

0.95

Mechanical transmission efficiency ηm

0.99

Combustion efficiency ηb

Combustion chamber pressure loss ∆Pb

0.98

4% of compressor outlet pressure.

C.V of fuel is 43,000 KJ/Kg, assume data if necessary, Cpa ≠ Cpg 16

3. (a) Explain with neat sketch operating principles of turbofan engine 8 (b) What is thrust augmentation? Explain any two methods of thrust augmentation with

sketches. 8

4. Compare the characteristics, advantages & disadvantages of turbojet, turbofan and turboprop engine.

5. (i)Discuss the different methods of thrust augmentation. Draw T-S diagram for turbojet engine with thrust augmentation. 8

(ii) Discuss the typical turbojet cycle performance with suitable sketches. 8

6. A turbojet engine is traveling at 270 m/s at an altitude of 5000m. The compressor pressure ratio is 8:1 and maximum cycle temperature is 1200K. By assuming the following data,

Ram efficiency 93% Isentropic efficiency of compressor 87%

Pressure loss in combustion chamber 4%of compressor delivery pressure

Calorific value of fuel 43,100 kj/kg Combustion efficiency 98% Mechanical transmission efficiency 99% Isentropic efficiency of turbine 90% Propelling nozzle efficiency 95% Ambient conditions at 5000 m are 0.5405 bar and 255.7 K.

Calculate the

(i) Specific thrust and

(ii) TSFC 16

7. (i) Define thrust of an engine and derive the thrust equation for a general propulsion system. 8

(ii) Discuss the typical turbojet cycle performance with suitable sketches. 8

8. An ideal turbojet flies at sea level at a Mach number of 0.75. It ingests 74.83 kg/s of air, and the compressor operates with a total pressure ratio of 15. The fuel has a heating value of 41,000 kj/kg, and the burner exit total temperature is 1389 K. Find the thrust developed and the TSFC. Assume that the specific heat ratio is 1.4. 16

9. Air enters a turbojet engine at a rate of 12*104 kg/h at 150C &1.03 bar and is compressed adiabatically to 1820C & four times the pressure. Products of combustion enter the turbine at

8150C & leave it at 6500C to enter the nozzle. Calculate the isentropic efficiency of the compressor, the power required to drive the compressor, the exit speed of gasses & thrust developed when flying at 800 km/h. Assume the isentropic efficiency of the turbine is same as that of the compressor and the nozzle efficiency is 90%.Assume the data required suitably. 16

10. A jet propelled plane consuming air at the rate of 18.2 kg/s is to fly at Mach number of 0.6 at an altitude of 4500m (Pa = 0.55 bar, Ta = 255K ). The diffuser which has a pressure coefficient of 0.9, decreases the flow to a negligible velocity. The compressor pressure ratio is 5 & maximum temperature in the combustion chamber is 1273 K. After expanding in the turbine, the gases continue to expand in the nozzle to a pressure of 0.69 bar. The isentropic efficiency of compressor, turbine and nozzle are 0.81, 0.85 & 0.915 respectively. The heating value of the fuel is 45870 kj/kg. Assume Cp = 1.005 kj/kg-K, Cpg = 1.147 kj/kg-K. Calculate

(i) Power input to the compressor

(ii) Power output of the turbine

(iii) The fuel air ratio

(iv) The thrust provided by the engine

(v) The thrust power developed. 16

1. (i) Explain successive steps in the acceleration and over speeding of a one- dimensional supersonic inlet with sketches. 8

(ii) Derive the relation between area ratio Amax/Ai and external deceleration ratio ui/ua. 8

2. A supersonic inlet is designed with a two-dimensional conical spike (with two half-cone angles 100 and 200 relative to the axial centerline, respectively). The inlet is to operate at a flight Mach number of 1.9.The two standing oblique shocks are attached to the spike and cowl, and a converging inlet section with a throat of area A* is used to decelerate the flow through internal compression. Assume γ = 1.4 and internal diffuser pressure recover factor Πr = 0.97. Estimate the overall recovery factor Πd on the assumption that the inlet starts (i.e., the normal shock is swallowed). Also, find the required A*/A1.

3. What are the different modes of inlet operation? Explain with suitable sketches. 16

4. Air enters a two-dimensional supersonic diffuser at a pressure of 14.102 kPa, a temperature of

217 K, and with a Mach number of 3.0. The two-dimensional oblique shock diffuser has an oblique shock angle of 27.80, which is followed by a normal shock. Determine, assuming constant specific heats.

(i) The velocity, total temperature and pressure of the air entering the oblique shock. (ii) The Mach number, total pressure after the oblique shock.

(iii) The flow deflection angle.

(iv) The Mach number, total and static pressure and static temperature after the normal shock.


UNIT-III

1. (a) What are the important factors affecting combustor design? 8 (b)Write down the methods of flame stabilization and explain with sketch. 8

2. (a)What are the three types of combustion chamber? Compare its advantages and disadvantages. 8

(b) Name the material used for combustion chamber and discuss the special qualities of the material used for combustion chamber? 8

3. (a)What are the factors affecting combustion chamber? Explain briefly? 8

(b) With the aid of a simplified picture explain the operation of a flame holder. 8

4. (i) With a neat sketch explain the working of a combustion chamber. 8

(ii) Consider n-decane fuel, balance the chemical equation for the stoichiometric combustion of this fuel in air and find the stoichiometric fuel-to-air ratio. 8


UNIT-IV

1. (a) Plot Mach number, static temperature, static pressure and static density variations along the longitudinal axis of a convergent-divergent nozzle, when it flows full. Explain the variations. 8

(b)A De Laval nozzle has to be designed for an exit Mach number of 1.5 with exit diameter of

200 mm. Find the ratio of throat area/exit area necessary. The reservoir conditions are given as Po = 106 Pa, To = 200C. Find also the maximum mass flow rate through the nozzle. What will be the exit pressure and temperature? 8

2. A converging-diverging is designed to operate with an exit Mach number of 1.75. The nozzle is supplied from an air reservoir at 68bar (abs.). Assuming 1-d flow, calculate:

(i) Maximum backpressure to choke the nozzle. 4 (ii) Range of backpressure over which a normal shock will appear in the nozzle. 4 (iii) Back pressure for the nozzle to be perfectly expanded to design M. 4 (iv) Range of back pressure for supersonic flow at the nozzle exit plane. 4

3. (i) What are the types of nozzle? Explain various operating conditions of a C-D nozzle with suitable sketch. 8

(ii) Write short notes on the following:

(a) Ejector and variable area nozzles 4 (b) Thrust reversing 4

1. An axial compressor stage has a mean diameter of 60cm and runs at 15000rpm. If the actual temperature rise and pressure ratio developed are 300C and 1.4 respectively.

(i) The power required to drive the compressor while delivering 57 Kg/s of air; assume mechanical efficiency of 86 % and an initial temperature of 350C.

(ii) The stage loading coefficient. (iii) The stage efficiency and

(iv) The degree of reaction if the temperature at the rotor exits is 550C.

2. (i) Explain the working of a centrifugal compressor and draw the velocity

triangles. 8

(ii) A centrifugal compressor has an impeller tip speed of 366 m/s. Determine the absolute Mach number of the flow leaving the radial vanes of the impeller when the radial component of velocity at impeller exit is 30.5 m/s and the slip factor is 0.9. Given that the flow area at impeller exit is 0.1m2 and the total-to-total efficiency of the impeller is 90%, determine the mass flow rate. 8

3. (i) A sixteen-stage axial flow compressor is to have a pressure ratio of 6.3. Tests have shown that a stage total-to-total efficiency of 0.9 can be obtained for each of the first six stages and 0.89 for each of the remaining ten stages. Assuming constant work done in each stage and similar stages fine the compressor overall total-to –total efficiency. For a mass flow rate of 40 kg/s determine the power required by the compressor. Assume an inlet total temperature of 288

K. 8

(ii) Discuss the factors affecting stage pressure rise of an axial flow compressor with suitable sketches. 8

4. A stage of a radial compressor is to be analyzed. It rotates at 12,300 rpm and compresses

31.75 kg/s of air. The inlet pressure and temperature are 241.325 kPa and 306K respectively. The hub and tip radii of the blades at the inlet are 7.62 and 13.97cm respectively. The exit radius is

27.94cm and the exit blade height is 2.54cm. The slip factor is unity. Flow enters the inducer with no prewhirl and the impeller has straight radial blades. The efficiency of the stage is 88%. The value of Cp and γ are 1.005 kj/kg-K and 1.397 respectively.

Find the following:

(i) Mean relative flow angle at the inlet.

(ii) The static pressure at the impeller exit. (iii) The total pressure ratio for the stage,

(iv) The Mach numbers at the impeller inlet and exit.

(v) The required power for the stage. 16

5. An axial flow compressor stage is designed to give free-vortex tangential velocity distributions for all radii before and after the rotor blade row. The tip diameter is constant and 1.0m; the hub

diameter is 0.9m and constant for the stage. at the rotor tip the flow angles are as follows: 16

Absolute inlet angle, α1 = 300

Relative inlet angle, β1 = 600

Absolute outlet angle, α2 = 600

Relative outlet angle, β2 = 300

.Determine,

(i) the axial velocity

(ii) the mass flow rate

(iii) the power absorbed by the stage

(iv) the flow angles at the hub

(v) the reaction ratio of the state at the hub

Given that the rotational speed of the rotor is 6000 rpm and the gas density is 1.5 kg/m3 which can be assumed constant for the stage. It can be further assumed that stagnation enthalpy and entropy are constant and after the rotor row.

6. The mass flow rate of flow at 288 K and 101.3 KPa at the inlet to the impeller of the centrifugal-flow compressor is 1.814 kg/s. The inlet flow is in the axial direction. The impeller eye has the minimum diameter of 3.81cm and a maximum diameter of 12.7cm and rotates at

35,000rpm. Assuming no blockage due to the blade, calculate the ideal angle at the hub and tip at the inlet to the impeller. Draw velocity diagram at the hub and at the tip

No comments:

Post a Comment